
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
= Adaptec Ultra160 Family Manager Set v1.11 =
=                                           =
=      README for Microsoft Windows 95      =
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=  


The following information is available in this README file: 

  o  Supported Hardware 
  o  Changes From Prior Release 
  o  Installation Instructions 
      - Installing the Driver When Installing Windows 95 
      - Updating the Driver for Windows 95 (Retail Edition) 
      - Updating the Driver for Windows 95 (OSR2.x)
  o  Known Issues 
  o  Contacting Adaptec 
  

Supported Hardware 

The following Adaptec SCSI Host Adapters are supported by the Adaptec Ultra160 
Family Manager Set v1.11. 

AIC-7892          Single Channel PCI-to-Ultra160 SCSI ASIC
AIC-7899          Dual Channel PCI-to-Ultra160 SCSI ASIC
AHA-3960D/39160   Dual Channel 64-bit PCI-to-Ultra160 SCSI Host Adapter
29160             Single Channel 64-bit PCI-to-Ultra160 SCSI Host Adapter
29160LP           Single Channel 64-bit PCI-to-Ultra160 SCSI Host Adapter(OEM)
29160N            Single Channel 32-bit PCI-to-Ultra160 SCSI Host Adapter (OEM)
19160             Single Channel 32-bit PCI-to-Ultra160 SCSI Host Adapter 
                  (Retail)
    
Changes From Prior Release 
   -  Support for Adaptec SCSI Card 19160
   -  Support for Adaptec SCSI Card 29160LP


Installation Instructions 

If you are performing a first time Windows 95 installation, see the
"Installing the Driver When Installing Windows 95" section, below.  If
Windows 95 is already installed on your system, see the "Updating the Driver
for Windows 95" section.
For more complete instructions, the Ultra160 FMS User's Guide is available 
online.  Please see the support section at http://www.adaptec.com/support/ . 

NOTE: Windows 95 shipped in two different version - the Retail Edition and the 
OEM Service Release 2 (or OSR2) Edition.  Both versions function the same, but 
the process of installing drivers is different. 

To determine which version you have, follow these steps: 
1. Select Control Panel under Settings from the Start Menu. 
2. Double-click the "System" icon. 
3. Under the "General" tab, it will display the version number of Windows 95 
   under the System category. 
4. If it displays "4.00.950", you have the Retail Edition installed.  If it 
   displays "4.00.950 B" or "4.00.950 C", you have OSR2.x installed.


Installing the Driver When Installing Windows 95
 
    1. Create the Windows 95 driver diskette.  Refer to the Family Manager Set 
    QuickStart Guide section "Creating Family Manager Set Driver Disks".
    Note: Follow the Windows 95 installation manual to install Windows 95.  If 
    your Windows 95 CD came with a Windows 95 Boot Diskette, and you are  
    installing from a CD-ROM attached to an Adaptec SCSI adapter, you will
    need to update the Windows 95 Boot Disk. Copy the file ASPI8U2.SYS and
    ASPICD.SYS from the Adaptec Family Manager Set Utility diskette to the
    Windows 95 Boot Disk. Refer to the section "Creating a DOS bootable 
    floppy for your SCSI adapter", in the Utility Disk Readdos.txt file, 
    if you are unsure how to do this.
 
    2. If "New Hardware Found" is displayed, select "Driver from disk provided 
    by hardware manufacturer". 

    3. Insert the driver diskette created in step 1 into the floppy 
    drive and type a:\win9x as the path; follow the on-screen instructions. 

    4. If you are prompted to reboot the system, select "no" if you have a
    dual channel adapter or if you  have multiple Ultra160 adapters. Then
    repeat steps 1 through 3 for each SCSI channel until all Ultra160
    adapters are found. Otherwise, select "Yes" to reboot the system. 
 
    NOTE: If you do not see "New Hardware Found", you might need to add the 
    driver manually. Once Windows 95 is installed, follow the steps in the 
    section titled "Updating the Driver for Windows 95 (Retail Edition)" or 
    "Updating the Driver for Windows 95 (OSR2.x)"  to verify that the drivers 
    have been added and are working properly. If a yellow question mark
    labeled PCI SCSI Bus Controller is displayed, update the driver as
    described.


Updating the Driver for Windows 95 (Retail Edition) 

To update or install the ADPU160M.MPD driver if Windows 95 is already
installed, follow these instructions: 
1. Start Windows 95. 
2. Click the Start button on the Windows 95 task bar, and then point to 
   Settings. 
3. Click Control Panel. 
4. Double-click the System icon. 
5. On the Device Manager tab, click the plus sign next to the SCSI controller 
   icon. 

NOTE:  If Windows 95 cannot determine the type of host adapter installed in
your computer, a yellow question mark labeled Other devices appears instead
of the SCSI controller icon.  To continue, click the plus sign next to the
question mark; a yellow question mark labeled PCI SCSI Bus Controller then
appears.

6. Double-click the Ultra160 Family host adapter you wish to update, or if a 
   yellow question mark labeled PCI SCSI Bus Controller is displayed,
   double-click the question mark. 
7. Insert the Adaptec Family Manager Set CD-ROM into your CD-ROM reader. 
8. Select the Driver tab. 

NOTE:  If the version of Windows 95 you are using now displays a window with a 
Update Driver button instead of a Change Driver button, the remainder of your 
install procedure is covered in Updating the Driver for Windows 95, Version
OSR2.x, described below. 

9. Click Change Driver.  You may be asked to select the hardware type; if so, 
   select SCSI Controllers. 
10. Click the Have Disk button and enter "d:\fmsimage\fms111\windows\win9x"
    as the path. (Note: Replace d:\ with the drive letter of your CD-ROM if different.)
11. Click OK. 
12. Select the Adaptec Ultra160 Family host adapter, and click OK. 
13. Again, click OK.  The driver is now installed. 
14. You must restart your computer for the changes to take effect.  Click Yes to 
    restart your computer.  Click No to return to the system properties window.
 

Updating the Driver for Windows 95 (OSR2.x)
 
This section covers the remaining steps to updating the driver on Windows 95 
OSR2.x. 
NOTE:  If you have not already done so, follow the instructions in "Updating
the Driver for Windows 95" section above. 

1. Click Update Driver. 
2. Insert the Adaptec Family Manager Set CD-ROM into your CD-ROM reader. 
3. In the Update Device Driver Wizard, select Yes, and click Next. 
4. Select Other locations. 
5. Under the Location edit box, type d:\fmsimage\fms111\windows\win9x, 
   then click OK. (Note: Replace d: with the drive letter of your CD-ROM if
   different.)
6. Click the Finish button. The driver is now installed. 
7. You must restart your computer for the changes to take effect.  Click Yes
   to restart your computer.  Click No to return to the system properties window. 

NOTE: If you attempt to re-update the driver again, at step 3 above you will 
need to select No, click Next, and follow the on-screen instructions to 
re-update. 
  

Known Issues 

 o  In some cases, each channel of a multichannel adapter must be 
    updated/installed manually with the ADPU160M.MPD driver on a freshly 
    installed Windows 95 system. Please follow the instructions listed under 
    "Updating the Driver for Windows 95" for each channel. 
    
 o  You will need to load the ASPI drivers (including MSCDEX.EXE, if you have 
    CD-ROM drive) if any of the following are true: 
        You are running in MS-DOS mode and need to access your CD-ROM drive. 
        You are using a scanner or another SCSI device with CONFIG.SYS or 
        AUTOEXEC.BAT based drivers, such as HP's SJIIX.SYS. 
        You have an older model SCSI-1 CD-ROM driver that Windows 95 does not 
        support. 
        You are using a CD-Recorder drive (however, some newer models of 
        CD-Recorder drives can use the embedded Windows drivers). 

 o  Some older models of SCSI CD-ROM drives are not compatible with the embedded 
    Windows 95 CD-ROM driver.  You can add support for the CD-ROM drive by doing 
    the following: 
        Make sure your ASPI real mode drivers (including ASPI8U2.SYS, ASPICD.SYS 
        and MSCDEX.EXE) are loaded and running from your CONFIG.SYS and 
        AUTOEXEC.BAT files. 
        If the first step did not work, find the file named CDTSD.VXD in the 
        \windows\system\iosubsys directory, rename it to CDTSD.SAV and reboot 
        your system. 

 o  The mapping between MSCDEX.EXE, which runs in real mode, and the Windows 95 
    CD-ROM driver does not match.  You can correct this in one of two ways: 
        Comment out the line that loads mscdex.exe in the autoexec.bat file. 
        Change the /L switch on the line that loads mscdex.exe in the 
        AUTOEXEC.BAT file so it assigns the CD-ROM drive the next highest 
        logical drive letter after the hard disk drives. 

 o  Windows 95 does not support sharing of system interrupts (also known as 
    IRQs) between two or more I/O subsystem devices (i.e. network interface 
    cards or hard disk adapters such as SCSI host adapters). When IRQs are 
    shared between I/O devices, lockups can occur while booting. If lockups 
    occur, try moving or removing one or more PCI cards from one slot to another 
    and bootup your computer again.  If problems continue, refer to your system 
    documentation and/or your system technical support for information on adding 
    your system configuration. 

 o  Certain older hard drives (Ultra-SCSI and lower) do not meet certain SCSI 
    timing requirements, and can cause the operating system to fail to boot.  It 
    is recommended that the firmware on the hard drive is updated or the drive 
    is moved to the Fast/Wide segment (SE connector) on the host adapter where 
    the commands of these drives can be buffered. 

    
Contacting Adaptec 

Technical information, including product literature, answers to commonly asked 
questions, information on software upgrades, and other topics is available 
electronically through the following: 

   o  Search the Adaptec World Wide Web site at http://www.adaptec.com 
   o  Connect to the File Transfer Protocol (FTP) server at 
      ftp://ftp.adaptec.com/pub/BBS/ 
   o  Search the Adaptec Support Knowledgebase (A.S.K.) at http://ask.adaptec.com 
      for articles, troubleshooting tips, and frequently asked questions for your 
      product. 
   o  For Internet support, send technical questions to Adaptec's Technical 
      Support Specialists via WebMail at 
      http://www.adaptec.com/support/webmail.html . 
   o  To speak with a Technical Support Specialist, call 408-934-7274, 
      Monday-Friday, 6:00 A.M. to 5:00 P.M., Pacific Time.

  
  
